Surface finish is one of the last decisions made on a tile specification and one of the hardest to change once installed. The same colourway can perform very differently as a matt, lappato or gloss surface. That difference shows up in how a space handles light, how safe it is underfoot and how much time a facilities team spends keeping it presentable.
In this post, our tile technicians will outline the trade-offs between matt and gloss finishes for commercial interiors.
We'll cover aspects such as glare under workplace lighting, slip performance, cleaning load and long-term wear.
For tailored advice on a commercial project please see our contact information at the end of this post.
Matt and gloss are ends of a spectrum

The choice is rarely a straight pick between two surfaces. Most commercial ranges sit somewhere along a scale of sheen. Each point on that scale changes how light, water and dirt behave on the tile.
- Matt: a low-sheen surface that scatters light rather than reflecting it. On porcelain this is often the natural, unpolished face of the tile. Matt tiles are the default for most commercial floors.
- Soft-touch or satin: a matt surface with a smoother feel. It reads as matt from most angles but can show a gentle sheen under raking light.
- Structured or grip: a matt surface with added texture for higher slip resistance. It is used in entrances, wet areas and external zones.
- Lappato or semi-polished: porcelain lightly polished so the high points of the surface take a sheen while the low points stay matt.
- Polished: fully polished porcelain with a mirror-like finish. It is achieved by grinding and polishing the tile body itself.
- Gloss: a glossy glaze fired onto the surface. This is common on ceramic wall tiles and differs from polished porcelain in how it wears.
The distinction between a gloss glaze and a polished body matters for specification. A gloss glaze is a coating, so scratches and wear show through it as dull marks. Polished porcelain loses its sheen gradually in traffic paths instead. On through-body porcelain the colour also continues beneath the surface.
Glare and reflectance under workplace lighting

Shop the look:
Gloss surfaces reflect light in one direction, much like a mirror. Matt surfaces scatter it evenly. In a workplace that difference decides whether a floor or wall adds to visual comfort or works against it.
Specular glare
A polished or gloss floor reflects downlights, linear luminaires and windows as bright patches. In an open-plan office those reflections move as people walk and can sit in the line of sight of screen users. BS EN 12464-1, the standard for lighting indoor workplaces, recommends matt surface finishes to limit reflected glare. It also suggests floor reflectances of roughly 0.2 to 0.4, compared with 0.5 to 0.8 for walls.
Sheen is not the same as LRV
Light reflectance value (LRV) measures how much light a colour reflects overall, from 0 for black to 100 for white. A pale matt tile and a pale gloss tile can share the same LRV. The gloss version concentrates that light into hotspots while the matt version spreads it. Specify LRV for brightness and contrast. Specify finish for glare.
Accessibility
BS 8300 and Approved Document M use LRV contrast, typically a difference of at least 30 points, to help people with visual impairments read where floors meet walls. Shiny floors can undermine this. Reflections can be read as wet patches or changes in level, which causes hesitation and confusion. A matt floor with a contrasting tiled skirting or wall gives a clearer edge.
Where gloss helps
On walls, gloss can lift a space with little daylight by bouncing light back into the room. It suits washroom walls, back-of-house corridors and feature walls viewed side-on rather than at screen height. Ceramic wall ranges such as Matrix come in matt and gloss across 23 colours. This lets the same colour be used for a reflective wall and a matt counterpart elsewhere in the scheme.
Slip performance

Shop the look:
Finish has a direct effect on slip resistance, most of all when a floor is wet. Gloss and polished floors usually perform well when dry and clean. Once water, grease or tracked-in rain is present their wet results tend to drop sharply.
In the UK, floor slip resistance is assessed with the pendulum test to BS 7976-2, which gives a Pendulum Test Value. The HSE and the UK Slip Resistance Group classify results as follows:
- 0 to 24: high slip potential
- 25 to 35: moderate slip potential
- 36 and above: low slip potential
Our guide on what PTV is and how slip ratings work explains the test in more detail.
Points to check on any finish:
- Ask for wet results. A dry PTV says little about how a floor behaves at an entrance on a rainy day. Wet values with the standard Slider 96 rubber reflect shod pedestrians. Slider 55 results are relevant where people walk barefoot.
- Don't assume matt means safe. Many matt tiles exceed 36 wet. Not all do. Smooth soft-touch finishes can test lower than they look. Specify against test data, not appearance.
- Treat R ratings with care. R ratings come from the German DIN 51130 ramp test with oil and shod feet. They are useful for industrial and commercial kitchen floors but do not convert directly to PTV. A comparison of R ratings vs PTV covers where each applies.
- Plan for the life of the floor. Slip resistance changes in service. Wear can smooth a textured surface. The wrong cleaning product can also leave a film that cuts grip.
Polished and gloss floors can still have a place in a commercial project. They suit dry, controlled areas such as executive suites, showrooms and upper-floor receptions served by lifts. Even there they need generous entrance matting and a reliable cleaning routine. The question of whether porcelain tiles are slippery usually comes down to finish rather than material.
Cleaning and maintenance load
Finish shapes how often a floor needs cleaning to look acceptable, not only how easy it is to clean. That makes it a running cost for the building owner rather than a one-off design choice.
Gloss shows everything. A reflective surface highlights footprints, smears, water marks and streaks left by poorly rinsed detergent. In a busy reception or lift lobby, gloss floors can need attention several times a day to keep their intended look. Gloss walls in washrooms show splashes and limescale in the same way.
Matt hides day-to-day marks. A matt surface disguises light soiling and drying marks well, which suits high-footfall areas cleaned on a fixed schedule. The trade-off is texture. Structured and grip finishes hold more dirt in their profile and need mechanical cleaning to stay effective.
Match the regime to the finish. Points to agree with the facilities team at specification stage:
- Rotary scrubber or scrubber-dryer with suitable brushes for textured finishes, rather than mopping alone, which spreads dirt across the profile
- pH-neutral cleaners for routine use on most porcelain, with stronger products only where the manufacturer approves them
- No wax, polish or film-forming products on slip-resistant floors, since these can reduce wet PTV
- Thorough rinsing on gloss and polished floors to avoid streaking
- A protective treatment where a polished porcelain manufacturer recommends one, to resist staining in open micro-pores
Detailing reduces the load. Grout and junctions trap dirt on any finish. Narrow joints with a stain-resistant grout in a tone close to the tile reduce visible soiling, as covered in this guide to choosing a grout colour. A tiled skirting also removes the hard-to-clean junction between floor and wall.
Wear, scratching and finish retention
A finish should be judged on how it looks after five years of traffic, not on the day of handover. Matt surfaces generally age most evenly. Gloss and polished surfaces show wear first.
- Grit is the main enemy. Sand and grit carried in on footwear act as an abrasive. On gloss glazes this leaves fine scratches that show as a dull haze in walking lines.
- Check abrasion data. Glazed tiles are classed for surface abrasion to BS EN ISO 10545-7, often quoted as a PEI class from 0 to 5. Commercial floors with heavy footfall typically need class 4 or 5. Unglazed porcelain is tested for deep abrasion to BS EN ISO 10545-6 instead.
- Polished porcelain dulls unevenly. Its sheen holds up in quiet areas but softens along desire lines. Over time this creates visible contrast between worn and unworn parts of the same floor.
- Matt ages consistently. A matt or structured surface has less sheen to lose, so wear is harder to see. This is one reason matt dominates commercial floor tiles in offices, retail and education.
Where a project wants a polished look in one area and a hard-wearing finish elsewhere, ranges with several surfaces help. The Regal porcelain collection combines different surface effects and slip-resistant options with matching trims, thresholds and grouts. This lets the finish change by zone while colour stays consistent.
Entrance matting deserves the same attention as the tile. A recessed matting system long enough to take several full strides removes much of the grit before it reaches the floor. It protects any finish but makes the biggest difference to gloss and polished surfaces.
Colour, material character and design intent
Finish changes how a colour reads as much as how it performs. The same pigment can look like two different products depending on its surface.
- Gloss intensifies colour. A glossy glaze deepens saturation and gives a crisp, clean edge to strong colours. It suits brand colours in retail, statement bars in hospitality and coloured washroom walls.
- Matt reads as material. Stone, concrete and terrazzo effects look most convincing in matt because the real materials are rarely glossy. A concrete-look porcelain such as Boston relies on its matt finish and natural variation for an authentic surface.
- Colour shifts between finishes. A matt and a gloss tile from the same range are not always an exact visual match. Matt versions usually appear slightly lighter and softer. Compare both side by side under the project's lighting before mixing them.
- Relief and texture add their own light play. Fluted, ribbed and 3D wall tiles create shadow lines that change through the day. A gloss glaze on a relief surface catches highlights along each edge. Ideas for using them are covered in this article on 3D wall tiles and how to use them.
Touch matters too. Matt and soft-touch finishes feel warmer and less clinical, which suits hospitality and workplace breakout areas. Gloss reads as hygienic and easy to wipe, which suits washrooms and food preparation walls.
Matching finish to each zone

Shop the look:
Most commercial projects need more than one finish. The right choice depends on what each zone is exposed to: water, grit, grease, screen work or close inspection.
- Entrances and receptions: matt or structured floors with a wet PTV of 36 or above, backed by entrance matting. Reserve polished floors for receptions away from the external door, such as upper-floor lobbies.
- Open-plan offices and workspaces: matt floors to control glare at screen height. Gloss works on feature walls outside the main sightlines from desks.
- Corridors and circulation: matt floors for consistent wear along long walking lines. Specify LRV contrast between floor and walls for wayfinding. A range of corridor tiles suits these routes.
- Washrooms: slip-resistant matt floors rated for wet conditions, with gloss or matt walls. Gloss walls are easy to wipe but show splashes and limescale more readily.
- Tea points and commercial kitchens: structured floors with suitable wet and contaminated slip ratings. Use gloss or satin walls behind preparation areas for easy cleaning. Commercial kitchen tiles are selected with grease and heavy cleaning in mind.
- Retail and showrooms: lappato or polished floors in dry, controlled areas where the look justifies the cleaning load. Switch to matt at entrances, changing rooms and stockrooms.
- Restaurants and bars: matt or soft-touch floors in front of house, since drink spills are common. Gloss suits bar fronts and walls. The range of restaurant tiles covers both floor and wall needs.
Combining finishes in one scheme
Using matt and gloss together lets a scheme balance performance with visual interest. It works best when the change looks deliberate.
- Change finish at a logical boundary. A doorway, threshold or change of use makes a clean break. A change in the middle of an open floor can look like a mistake or a worn patch.
- Keep formats and thicknesses aligned. Tiles from the same range in different finishes are not always identical in thickness. Check this early to avoid lips at transitions.
- Use one colourway across finishes. A single colour in matt on the floor and gloss on the walls ties a room together while each surface does its own job.
- Mark finishes clearly on drawings. Finish is easy to lose in substitutions on site. Name the finish in schedules and drawings as well as the product, and include the required slip rating for each floor zone.
Specification checklist
Before finalising a matt or gloss finish, confirm the following for each zone:
- Wet PTV results to BS 7976-2, plus R or barefoot ratings where the use calls for them
- Abrasion class or deep abrasion data suited to expected footfall
- Glare risk from luminaires and windows, especially near screen-based work
- LRV contrast between floor, walls and key fittings
- The cleaning regime the facilities team can realistically deliver
- Entrance matting length and type
- Colour match and thickness between finishes where they meet
Specify the right finish with Parkside
Parkside's specification consultants work with architects, designers and contractors to match tile finishes to the demands of each space. They can advise on slip test data, abrasion performance and finish options across porcelain, ceramic and natural stone ranges.
To discuss a project, contact the Parkside team.


